dbc-sf-s/s2/d digital dvb-s2 satellite signal finder
/ dbc-sf-s/s2/d digital dvb-s2 satellite finder
SETTINGS OF DIGITAL SATELLITE FINDER DBC- SF- S / S2- D
VIDEOCON D2H, TATA SKY, DISH TV, ZING TV TRANSPONDER SETTINGS
DD DIRECT+ @93* EAST INSAT 4B
TRANSPONDER SYMBOL RATE POLARIZATION FEC 11090 27500 VER 3/4
11030 27500 VER 3/4
11070 27500 VER 3/4
11110 27500 VER 3/4
11150 27500 VER 3/4
11185 27500 VER 3/4
DISH TV @95* EAST NSS6
TRANSPONDER SYMBOL RATE POLARIZATION FEC 12688 27500 VER 3/4
12595 40700 VER 3/4
12534 40700 VER 3/4
11172 27500 HOR 3/4
11038 40700 HOR 3/4
10990 27500 VER 3/4
12647 27500 HOR 3/4
12595 40700 HOR 3/4
TATASKY @83*EAST INSAT4A
TRANSPONDER SYMBOL RATE POLARIZATION FEC 10970 28500 HOR 5/6
11010 27500 HOR 3/4
11050 28500 HOR 5/6
11090 28500 HOR 5/6
11130 28500 HOR 5/6
11170 28500 HOR 5/6
11470 28500 HOR 5/6
11510 28500 HOR 5/6
11550 28500 HOR 5/6
11558 13328 VER 3/4
11592 28500 HOR 5/6
11630 28500 HOR 5/6
11670 28500 HOR 5/6
VIDEOCON d2h @88*EAST ST-2
TRANSPONDER SYMBOL RATE POLARIZATION FEC 11483 43978 VER 2/3
11609 43978 VER 2/3
11609 43978 HOR 2/3
11672 43978 VER 2/3
11672 43978 HOR 2/3
FOR AIRTEL DIGITAL FREQUENCY SET UP - READ THIS
NOTE : Which Transponder, Symbol Rate , Polarization are in BOLD letter these are you can add to your sat finder and show signal strength and quality . This is tested my self. If any query you can comment me in button of this page.
USER MANUAL
SAFETY USE
· Please read this manual carefully before first time use.
· Don ‘t place heavy items on the device.
· Do not lay the device close to heating source, in the sunshine, in place with strong vibration or full of dust.
· Clean the device with soft dry fabric, do not drop liquid in to the device to prevent damage.
· Place the device in ventilated surroundings.
· Contact the provider should malfunction happen.
· Damaging the device on operation without notice in order to iprove design and supply the best possible product. Accordingly operation method may change. If you have any question, please consult the manufacturer.
NOTICE
1. Do not use two different power sources simultaneously.
2. If utilize satellite receiver to supply power, 18v setting and current capacity > 500 mA is better , otherwise use power adaptor insted.
3. Use the compass attached for directional reference before power on, otherwise it will be affected by magnetic field of current.
4. If short circuit happens when connecting cable the screen will show “Input signal circuit! Please power off!” or flash, please check and remove the problem, then connect power again.
2. features
· Capable to edit transponder , symbol rate and LO frequency etc.
· Accurate and convenient facility for antenna installation
· Support 0/22 KHz control
· With signal strength and quality display
· Support DVB-S and DVB-S2 function
3. Panel introduction
1. Signal input ( from LNB)
2. Signal Output ( To receiver)
3. Dc input
4. UP : move cursor up
5. DOWN : move cursor down
6. LEFT : move cursor left
7. RIGHT : move cursor right
8. OK: Confirm ( Enter )
9. EXIT : Exit ( Cancel )
10. Compass
11. Buzzer
5. Main menu operation description
The screen will show “welcome! Initializing now, please wait a moment” temporarily when power is connected, then enter the main menu.
Press UP or DOWN button to move cursor to the function selected then press “OK” button to confirm (enter).
MAIN MENU
Find Satellite
List Satellite
Add Satellite
Edit Satellite
Add Transponder
Edit Transponder
Angle Calculation
4.1 Find satellite
Function
The function offers quick access of satellite, parameter selection and signal status display, It also can modify selected parameter directly.
Operation
Selected the function and press “ OK” button to enter the menu as following:
Sat name: vid d2h
LO Freq: universal
Down Freq: 11609
Symb Rate 43978
Polarity: ver
DiSEqC 1.0: OFF
22K: OFF Buzzer: OFF
S: 75% Q: 68%
1. Press “UP” or “DOWN” button to move cursor to “ Sat Name” , Press “LEFT” or “ RIGHT” button to select different satellite, Similarly, moving cursor to “LO Freq” or “ Down Freq” can select different local oscillator frequency of LNB or down link frequency, moving cursor to “ polarity” , “ diseqc 1.0” “22K” or “BUZZER” can select different control status respectively
2. If need to modify parameter, press ”UP” or “DOWN” button to move cursor to the selected parameter and press “ OK” button to enter setting function, press “LEFT” or “Right” button to select digit which you need to edit, then press “UP” or “DOWN” button to change number (number : 0~9), press “OK” button to confirm and exit the current setting.
When press ”EXIT” button to exit the menu. The screen will show “ Press OK to Save, other to EXIT. You can decide to save the last modification or not.
3. Move cursor to “S: Q:” and press “OK” button, the screen will show as following , this offers more obvious signal status inspection.
4. Press “EXIT” to exit current menu
4.2 List satellite
FUNCTION
The function can show all satellite message, transponders, signal strength and quality. It offers the convenience of check and operation.
OPERATION
OPERATION
Select “List satellite” and press “OK” to enter the following menu.
1 Press “UP” or “DOWN” button to select satellite, press “OK” to enter the transponder list of the satellite as following.
2. Press “UP” or “DOWN” button to move cursor, press “LEFT” or “RIGHT” button to change page. Select the transponder and press “OK” button to show the signal strength and quality as following.
3. Press “EXIT” button to exit current menu.
4.3 ADD SATELLITE
FUNCTION
According to the user’s requirement, they can add some new satellites. It includes satellite name, LO Frequency, 22KHz and DiSEqC 1.0 control.
OPERATION
Select and enter the “Add Satellite” menu as following.
1. Move cursor to “Name” and press “OK” button to enter adding satellite name function. Press “LEFT” or “RIGHT” to move cursor to selct the letter or digit position, then press “UP” or “DOWN” button to set the letter or number (capital: A~Z ; lowercase: a~z; number : 0~9), press “OK” button to confirm and exit current setting.
2. Press “UP” or “DOWN” button to move cursor to “LO Freq”, “22K” or “DiSEqC1.0”, then press “LEFT” or “RIGHT” to change setting respectively.
3. If need to modify LO frequency, move cursor to ”LO frequency “ and press “OK” button to enter modifying function, press “LEFT” or “RIGHT” button to select digit, then press “UP” or “DOWN” button to change number ( number :0~9), press “OK” button to confirm and exit the current setting.
4. Press “EXIT” to exit current menu when you finish this setting, and it will show “Press OK to SAVE, others to EXIT”, make a selection according to your requirement.
4.4 EDIT SATELLITE
FUNCTION
In this menu, user can edit satellite name, LO Frequency , 22KHz and DiSEqc1.0 control. Also you can delete current satellite.
Operation
Select and enter the “Edit Satellite” menu as following.
1. Move cursor to “Name” , press “LEFT” or “RIGHT” button to select satellite. If need to edit satellite name, press “OK” button to enter , press “LEFT” or “RIGHT” to select the letter or digit, then press “UP” or “ DOWN” button to change setting (capital: A~Z ; lowercase: a~z; number : 0~9),press “OK” button to confirm and exit current setting.
2. Press “UP” or down to move cursor to lo frequency 22k or diseqc1.0 , then press left or right to change setting respectively.
3. If need to modify lo frequency, move cursor to lo freq and press ok button to enter modifying function, press left or right button to left digit, then press up or down button to change the digit setting, press ok button to confirm and exit the current setting.
4. Press exit to exit current menu when you have finished setting, and it will show Data change! Press ok to SAVE, to others to EXIT, make a selection according to your requirement.
5. If select DEL Satellite and press ok button, it will show Are you sure to DEL? Press ok del, others to EXIT, make a selection according to your requirement.
4.5 Add Transponder
Function
According to the user’s requirement, they can add new transponders in this function.
Operation
Select and enter the “Add transponder” menu as following.
1. Press UP or DOWN button to move cursor to Satellite, press LEFT or RIGHT button to select the satellite. Polarity status can be set similarly.
2. Press UP or DOWN button to move cursor to down freq press OK button to enter, press LEFT or RIGHT button to select digit, then press UP or DOWN button to set the number (number:0~9) , press “OK” button to confirm and exit current setting. Symbol rate can be set with same procedure.
3. Press “EXIT” to exit current menu when you finish this setting, and it will show “Press OK to SAVE, other to EXIT”, make a selection according to your requirement.
4.6 Edit transponder
Function
User can edit all the transponders in this menu; also you can delete current transponder.
Operation
When you enter “Edit Transponder” menu, it will show the satellite list as following.
1. Press “UP” or “DOWN” button to move cursor, press “LEFT” or “RIGHT” button to enter different page, select the satellite and press “OK” button to enter “Edit Transponder” as following.
2. Press “UP” or “DOWN” button to move cursor to “Down Freq”, press “OK” button to enter setting, press “LEFT” or “RIGHT” button to select digit, then press “UP” or “DOWN” button to set the number (number : 0~9) press “OK” button to confirm and exit current setting .
3. Press “UP” or “DOWN” button to move cursor to “polarity , press “LEFT” or “RIGHT” button to change selection.
4. Press “EXIT” to exit current menu when you finish this setting, and it will show “Press OK to SAVE, others to EXIT”, make a selection according to your requirement.
5. Select “DEL Transponder” item to delete current transponder, and it will show “Are you sure to DEL? Press OK to DEL, others to EXIT”, make a selection according to your requirement.
4.7 Angle Calculation
Function
The function can calculate antenna elevation, azimuth and LNB polarization angle according to satellite longitude, local location longitude and hemisphere parameter setting; it is useful for receiving installation.
OPERATION
1. Move cursor to “Angle Calculation” press “OK” to enter as following.
2. Press “UP” or “DOWN” button to move cursor to the parameter and press “OK” button to enter, press “LEFT” or “RIGHT” button to select digit position, then press “UP” or “DOWN” button to set the number, press “OK” button to confirm and exit current setting.
3. The letter “E”, “W”, “N”, and “S” means east longitude, west longitude, north hemisphere and south hemisphere respectively. These letters can be set similarly.
4. The angle data can be calculated and displayed automatically when parameter is setting. Elevation angle is counted from horizon upward; azimuth angle is from north clockwise.
5. Press “EXIT” button to exit the menu.
5 SPECIFICATIONS:
1. Input frequency
Frequency range: 950 MHz ~ 2150 MHz
2. Input signal
Input level range: -25dBmV ~ 65dBmV
Input impedance: 75 Ohms
3. Others
Operating temperature: -10c ~ +50c
QPSK, 8PSK demodulation: supported
22 KHz control: supported
Connecters: F type female
4. Power
To LNB: 13V~ 18V,> 500Ma
Power supply input: AC 110 ~ 220 V 50Hz/60Hz
Power Supply Output: 13V DC 1000Ma
5. Attachments
Power supply: x1
Operation manual: x1
NOTE:
LI-ion battery (selectable)
Charger (selectable)
No comments:
Post a Comment